Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Styles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Hollywood?
Chimney cap installation in Hollywood typically runs $185 to $540, and a crown repair or rebuild generally lands between $300 and $1,400 depending on size and damage. A single-cap install with a standard stainless or galvanized model usually falls near the lower end, while multi-flue masonry chimneys on older Hollywood Hills homes push into the higher range. Most jobs are quoted on-site because the crown surface, flue count, and roofline access decide the final number.
We quote both together often, because a failing crown and a missing cap tend to show up on the same roof. One protects the flue from water and animals, the other sheds water off the masonry itself. When both are compromised, the chimney is taking water from two directions at once. Call (866) 520-4943 for a free estimate, and we’ll tell you which one needs attention first.
Key Takeaways
- Standard chimney caps in Hollywood run $185-$540 installed, depending on flue count and material.
- Crown repair (patching, sealing) costs $300-$650; a full crown rebuild runs $700-$1,400.
- Hollywood’s marine layer and Santa Ana wind cycles are hard on masonry crowns, so repair timing matters.
- We install professional-grade components from Olympia Chimney, Copperfield, Gelco, and Famco, not hardware-store substitutes.
- Free estimates, and we handle the repair ourselves rather than handing you off to a mason.
Chimney Cap & Crown Cost Breakdown (2026)
Here’s what Hollywood homeowners are paying this year. These ranges reflect real quotes for single-family homes and small multi-unit properties across the neighborhood, from flat-roof bungalows near Sunset Junction to hillside homes with steep pitched roofs.
| Service | Typical Cost Range | What’s Included |
|---|---|---|
| Single-flue cap (galvanized or stainless) | $185-$340 | Standard cap, fitted and secured |
| Multi-flue custom cap | $340-$540 | Fabricated cap sized to flue configuration |
| Decorative or copper cap | $450-$900 | Copper or specialty finish, custom fit |
| Crown crack sealing / patching | $300-$650 | Minor crack repair, sealant, wash coat |
| Crown rebuild (partial) | $700-$1,050 | Removing damaged section, new mortar crown |
| Full crown rebuild | $1,050-$1,400 | Complete crown removal and replacement |
| Cap + crown combined (common) | $500-$1,600 | Both services on the same visit |
What pushes a quote toward the top of these ranges? Deep crown cracks that have already let water into the masonry, unusual flue shapes (oval or rectangular), rooflines that require more careful access, and the age of the mortar itself. A crown that’s crumbling from the inside out can’t be saved with a coat of sealant, and we’ll tell you plainly when a rebuild is the only honest fix. A straightforward single-flue cap on a flat-roof Hollywood bungalow is usually a short, predictable job. A brown-shingle craftsman up a narrow street with limited parking and a pitched roof takes longer before we even touch the chimney.
What Affects Chimney Cap & Crown Pricing in Hollywood
No two Hollywood chimneys price the same. A few local realities move the number:
- Roof access and parking. Many Hollywood streets leave little room for a truck and ladder. Hillside properties near Beachwood Canyon and the Hollywoodland stairs can add setup time, which shows up in labor. If we can back the truck close, the job moves faster.
- Chimney age and construction. A large share of Hollywood housing stock dates to the 1920s and 1930s. Those masonry chimneys often have crowns that are original, and the mortar has had nearly a century of marine moisture and thermal swing. A 90-year-old crown sometimes needs a full rebuild where a newer one just needs sealing.
- Flue count and shape. One round flue under a standard cap is the simplest case. Two or three flues, or an unusual footprint, need a custom-fabricated cap. We build those from Copperfield, Olympia Chimney, Gelco, and Famco components sized to the actual flue.
- Whether the crown is cracked or crushed. Hairline cracks can be sealed. A crown that has separated from the flue or is spalling in chunks needs rebuilding. Sealing a structurally failed crown is money thrown away, and we won’t price it that way.
- Water damage already inside the masonry. If a missing cap let rain into the flue for a season, we may find a damaged liner underneath. We carry HeatShield ceramic resurfacing, which can restore a deteriorating liner without a full reline. That’s often the difference between a $400 fix and a $2,000 one, and it’s something a sweep-only crew can’t offer you.
- Whether you bundle both services. Combining a cap and crown on one visit is usually less than booking them separately, since we’re already up there with the chimney fully inspected.
California building code also requires caps with a spark arrestor on wood-burning chimneys (from our Los Angeles region a fair number sit close to brush, especially up in the hills). That’s a standard part of the cap, not an upsell, and a real cap does double duty: keeps animals and rain out, keeps embers in.
How to Save on Chimney Cap & Crown
Here’s where homeowners actually save real money instead of chasing a cheap quote that costs more later:
- Fix the cap before the crown fails. A cap is $185-$540. A full crown rebuild is $700-$1,400, and water inside the masonry can add a liner problem on top. Catching the missing cap early is the single biggest cost saver on this list.
- Bundle the visit. Cap and crown on the same appointment typically beats two separate trips. Ask us to quote both together.
- Fix cracks while they’re cracks. Crown sealing at $300-$650 is far less than a rebuild. Seal the small stuff, rebuild the real damage, and don’t pay for a patch that won’t hold.
- Ask about HeatShield before you assume a reline. If water’s already caused liner damage, ceramic resurfacing may save you the cost of a full reline. Get an honest diagnosis before anyone quotes you a liner.
- Get a written scope, not just a number. A good quote tells you what it covers. We’ll tell you what needs doing and what can wait.
Every estimate from us is free. Call (866) 520-4943 and we’ll come assess both cap and crown in one visit, then quote you a clear number.
A quick note on doing it yourself: chimney caps and crowns sit at the top of a roofline, and in Hollywood that often means steep pitches, tile roofs, and awkward ladder angles. Getting up there safely and doing the masonry right takes equipment and experience, and a poorly seated cap or a sealant-only crown fix leaks again within a season. If you’re looking at a repair up top, let a trained professional do it.
What’s the Difference Between a Cap and a Crown?
A chimney cap is the metal hood that sits over the flue opening; a crown is the concrete or mortar surface on top of the chimney stack that slopes water away from the flue. People mix them up because they live in the same place, but they do different jobs.
The cap is the recent addition, a metal cover with screening that stops rain, birds, squirrels, and embers from getting in or out. The crown is part of the chimney’s masonry structure, poured or formed to shed water off the top of the stack and away from the flue. When the crown cracks, water gets into the masonry. When the cap is missing, water and animals get straight down the flue. Both lead to expensive repairs if you wait. That’s why we recommend looking at both on the same inspection, and why a lot of our Hollywood calls start with a home inspector’s report pointing at one or the other.
Why We Use Professional-Grade Materials
We work with six recognized chimney-industry suppliers: DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, and Copperfield. That means the cap on your flue is the right one for your actual flue configuration, not a universal fit from the hardware store that rattles in the wind. It means the crown gets rebuilt with the right masonry and slope. And it means, when we find a liner problem underneath, we have HeatShield ceramic resurfacing available to restore it without a full reline in many cases.
We sweep it and we repair it. One company, no referrals, no handoff to a mason who never saw the original inspection. Chimney cleaning is where we start; understanding the system behind it is what we do. If a sweep turns up a cracked crown or a loose cap, we can resolve it ourselves. Dryer vents fall under the same roof, by the way: restricted, dirty ventilation turns into a fire whether it’s behind the fireplace or the laundry room. We treat both with the same seriousness. You can read more about how we approach chimney work before you call.
FAQs – Chimney Cap & Crown Cost
How much does a chimney cap cost in Hollywood?
A standard chimney cap in Hollywood runs $185 to $540 installed. A single-flue galvanized or stainless cap sits at the low end; a custom multi-flue or copper cap runs higher. Call (866) 520-4943 for an exact quote, and estimates are free.
How much does a chimney crown rebuild cost?
A full crown rebuild in Hollywood typically costs $1,050 to $1,400, while partial repairs or crack sealing run $300 to $650. The size of the chimney and how much mortar has failed decide the number. Call (866) 520-4943 to get yours priced on-site.
Is it cheaper to repair the crown or rebuild it?
Repair is cheaper at $300-$650, but only when the damage is surface-level. A crown that has separated from the flue or is spalling in chunks needs a rebuild at $700-$1,400, and sealing it instead just buys you one more leaky season. We’ll tell you honestly which one you need. Call (866) 520-4943 for a free assessment.
Can you install a cap and repair the crown in one visit?
Yes, in most cases we handle both on the same appointment, which usually costs less than booking them separately. We inspect the full chimney while we’re up there and quote both together. Call (866) 520-4943 to schedule.
Do the ocean air and marine layer in Hollywood really damage a chimney crown?
Yes. The coastal moisture and heat cycles across the region work mortar and concrete over time, and original crowns on 1920s and 1930s Hollywood homes are especially vulnerable. That’s why crown repair is one of our most common calls here. Call (866) 520-4943 if your crown looks cracked or chalky.
When you’re ready, we’ll look at the cap, the crown, and the liner underneath in a single visit, tell you what needs fixing now and what can wait, and quote you a clear price. One company for the diagnosis and the repair, working with professional-grade parts. Call (866) 520-4943 for a free estimate. You can also learn more on our Chimney Cap & Crown in Hollywood page.
Written by the team at Firebrick Chimney Sweep, serving Hollywood and the greater Los Angeles area. Pricing reflects the Hollywood market as of 2026. Firebrick Chimney Sweep offers free estimates – call (866) 520-4943.
What Our Customers Say
"Creosote buildup was worse than I realized. He measured it, showed me the glazing on the flue with the camera, and was honest that we were closer to a chimney fire than I wanted to hear."
— Scott Ziegler"Crown was cracked and taking water. Repaired it rather than quoting a rebuild, which the previous company had pushed hard for."
— Carmen Garcia"Swept it, capped it, and installed a proper damper. The downdraft smell in the summer that we'd lived with for years is gone."
— Gabriela Torres